M16A1 CLONE FOR SALE HOW TO EMBED PHOTOS

Clone of M16A1 variant of M16 rifle CQ-A, clone of M4A1 variant of M4.I'm a little embarassed to post after brilliant post yesterday, but by coincidence, another Texan built the same thing at the same time.About Our M16A1 Parts. Get Cheap Building A M16a1 Clone at best online store now Building A M16a1 Clone BY Building A M16a1 Clone in Articles Find out more Building A M16a1 Clone will be my personal favorite everything brought out the foregoing week.norinco m14 for sale us norinco firearms usa norinco cq chinese m14 clone norinco. Buy Building A M16a1 Clone Building A M16a1 Clone Reviews : You want to buy Building A M16a1 Clone.

Colt M16 Upper Receiver Group, complete re-issue. Buffer assembly and short upper buttplate screw sold. The buttstock assembly comes with a complete buttplate with a brand new plastic trap door and a reparkarized rear swivel and screw.

M16A1 Clone For Sale How To Embed Photos

I am NOT selling, but I hope it will be useful to my heirs when they inherit and dump my painstakingly acquired collection, God willing a long time from now.Semiautomatic AR15 built on a new BRN-16A1 lower receiver with all Vietnam-era GM Hydramatic M16A1 parts, serial number BRN7716. If somebody will tell me how to embed photos into my post, I'll plug them in here.Incidentally, I wrote this as a sales ad. Here is my long description, which is only possible from the amazing descriptions and photos our fellow Arfcommers have so freely offered.Description flows with this link. $100 shipped!I put this together piece by piece. Shockingly affordable, too.

The first was for 240,000 rifles, at $151.54 each, the second for 229,217 rifles priced at $99.74. GM filled two government contracts for M16A1s between February 1969 and June 1971. All other GM parts are in original, unrestored condition.GM Hydramatic M16 rifles account for fewer than 500,000 of the nearly 5,000,000 M16s the United States produced during the Vietnam War.

The dust cover has a small rectangle with rounded edges on the top center of the door. The front lug of the upper receiver is recessed on the left side, and both lugs are tapered on the sides.The center leg of the numeral “3” on the sight wheel “droops” as is normally seen on GM and some other rifles. The GM-common forging blemish on the front left side of the receiver, near where the gas tube enters the upper, is also present. The carrying handle displays horizontal machining marks on the front, semicircular machining marks above the gas tube, and a pronounced forging flash on the rear. Another blister/flaw runs along the bottom left edge of the receiver, to the rear of the magazine well. This rifle displays all the characteristics known to be present on GM-produced M16s.The carrying handle has a forging “blister” near the left sight screw at the five o’clock position, and also on both the right side at the top of the recess that is below the sight adjustment wheel, and the same location on the left side.

The bolt has the correct touching MP mark perpendicular to the extractor.The Brownell’s semi-automatic BRN-16A1 lower receiver is engraved with GM Hydramatic markings by Ident Marking Services of Rockwall, TX. The correct rubber-coated sling swivel is retained by a rivet rather than the more common roll pin.The charging handle has the expected six dots on its rear, and the bolt carrier has the rough tree bark-like machining marks running parallel to the guide rails on the front that identify a GM-produced bolt carrier. The front sight base has pronounced forging flashes on the front and rear. The bayonet lug is marked with a circled M over P. The front sight base is marked on the right with a sideways “10,” and on the left with a barely discernable upside-down “B”.

Both handguards display a “plus” sign and numeral on the inside toward the back of each handguard, and the front of the Type D buttstock shows the remains of a GM “plus” and the numeral “4”. The bolt catch has a circled number “3” on the leg.The fat pistol grip has a numeral “4” and the GM “plus” sign on the inside, and a letter “D” in the recess on top. The final approximately ¼” of the hammer spring legs angle in.

Hope this is a useful addition to AR15.com's wonderful knowledge library.